Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
Are you currently looking for tips concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically rocket science, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the project can relocate easily; if you have to open up a wall surface to eliminate the old bathtub and also position the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have certified yourself for the task and are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This post will help you mount a new bath tub in your shower room if you have already bought a new bathtub as well as don't require to change the setup of your previous water pipes.
Your devices and product checklist should make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome as a result of the limited gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required setting. The wood boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub till the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the supply of water and check all joints and also new pipework for leaks and tighten them if required. Fill the tub as well as likewise check the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used at least once as this will certainly resolve it into its final setting.
Preparing for the Setup
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, triggering the water to permeate the wall in between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can crack relatively early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very taken with How to Install a Bathtub Yourself and I am praying you enjoyed the piece. If you enjoyed our page if you please be sure to pass it around. We appreciate reading our article about How to Install a Bathtub Yourself.
Call Us Today Report this page